Brady B-534label_film_tape
Floor Marking Signs
Brady B-534 is a surface printed polyester with an anti-skid tread, used for marking aisles and exits, adhering to stainless steel with a permanent rubber-based adhesive.
Material Composition
surface printed polyester with a rigid, clear polyester overlaminate and selectively covered by an anti-skid tread
Adhesive System
Permanent rubber based adhesive
Operating Temperature
-18°C to 54°C (0°F to 129°F)
Total Thickness
11 mils (0.28 mm)
Industrial Safety & Asset Marker
B-534 Application & Installation Blueprint
Heavy-Duty Industrial Safety & Identification Marker • Physical application tolerances and surface engineering
Industrial Fit Certified
Standard Industrial Marking Procedure
1Ensure application surface is dry and free of loose particulate or heavy oil.
2Peel and apply with steady firm pressure from center to edge.
3Allow 24 hours for ultimate cross-linked adhesion strength.
Engineering Tolerance: Engineered to withstand standard industrial plant environmental conditions and indoor/outdoor temperature swings.
Substrate Compatibility & Adhesion Matrix
Smooth Metals & Stainless Steel
Standard Bond (5/5)
Rigid Thermoplastics & ABS
Standard Bond (4.8/5)
Painted Metal Cabinets
Standard Bond (4.8/5)
Glass & Smooth Composite
Standard Bond (4.8/5)
Tested Environmental Survivability
Industrial Plant Temperature SwingsDust, Grease & Mild FluidsStandard Abrasion & RubbingLong-Term Legend Legibility
Recommended Field & Shop Tools:
i3300 / i5100 Benchtop PrinterM210 / M610 Handheld ToolStandard Thermal Ribbon
Orderable Part Numbers, Packaging & Distributor SKUs
Official Brady SKUs, roll dimensions, package quantities, list pricing, Grainger part numbers, and printer compatibility for B-534.
Custom orderable roll sizes, continuous tapes, and die-cut parts for B-534 are available through authorized Brady distributors.
Quality Assurance, Storage & Regulatory Compliance
Standardized engineering guidelines for warehouse storage, application temperature, and agency certifications.
Shelf Life & Warehouse Storage
Expected Shelf Life: 1 Year from receipt
Storage Temperature: Below 80°F (27°C)
Relative Humidity: ≤ 60% RH
Must be stored in original packaging in a climate-controlled warehouse.
Application vs Service Limits
Min Application Temp: 50°F (10°C)
Service Temp Range: -18°C to 54°C (0°F to 129°F)
Full Cure / Dwell Time: 24 Hours (ASTM D1000)
Clean surface of oil/grease before bonding for maximum peel strength.
Agency Testing & File Directories
UL 969 / 2238: Non-approved variant
UL DirectoryCSA C22.2: Not certified
CSA DirectoryEnvironmental & Safety Standards
RoHS 3 Compliance:2011/65/EU (Pass 2015/863)
REACH Status:SVHC Free (<0.1% w/w)
CA Prop 65:Compliant Notice
Certificates of Conformance (CoC) available on order shipment.
Engineering Limitations & Chemical Fitness Warnings
Extracted directly from Brady Technical Data Sheets to prevent real-world application failures and chemical degradation:
- Not recommended for outdoor use
- Not recommended for outdoor use
Sponsored Industrial Label Solutions
Industrial Label Printers & Materials
Relevant Technical Equipment & Consumables [Ad Slot spec-mid-B-534]
ASTM Physical & Mechanical Properties
Standardized laboratory test data measured in accordance with ASTM D 1000, ASTM D 2979, and ASTM D 2671.
Thermal Transfer Ribbon Compatibility
Official Brady recommended ribbons engineered for maximum contrast, smear resistance, and UL certification compliance.
Recommended Thermal Transfer
Non-printable hardware, tag, or pre-printed material.
* Note: Testing print permanence with official Brady ribbons is required to maintain UL/CSA agency certification on printed labels.
Chemical & Solvent Resistance Matrix
Standardized dip and rub immersion test observations across industrial fuels, oils, solvents, and cleaners.
Tested per ASTM D 895 / Brady standard dip & rub immersion.
| Chemical Reagent / Solvent | Substrate / Adhesive Effect | Thermal Ribbon Permanence |
|---|---|---|
| 1A (10% Acetic Acid) | Tested | Tested |
| 1A (30% Sulfuric Acid) | Tested | Tested |
| 1A (50% Sodium Hydroxide) | Tested | Tested |
| 2A (10% Sodium Hydroxide) | Tested | Tested |
| 1B (MEK) | Tested | Tested |
| 1A (Acetone) | Tested | Tested |
| 1A (Toluene) | Tested | Tested |
| 1A (Methanol) | Tested | Tested |
| 1C (Isopropyl Alcohol) | Tested | Tested |
| 1E (Heptane) | Tested | Tested |
| 1E (Mineral Spirits) | Tested | Tested |
| 1D (Turpentine) | Tested | Tested |
| 1D (Diesel Fuel) | Tested | Tested |
| 1E (Kerosene) | Tested | Tested |
| 5E (Gasoline) | Tested | Tested |
| 1B (ASTM #3 Oil) | Tested | Tested |
| 1B (SAE 20 Oil) | Tested | Tested |
| 30% Sulfuric Acid | Tested | Tested |
| 10% Sulfuric Acid | Tested | Tested |
| 30% Hydrochloric Acid | Tested | Tested |
| 10% Hydrochloric Acid | Tested | Tested |
| Glacial Acetic Acid | Tested | Tested |
| 10% Acetic Acid | Tested | Tested |
| 50% Sodium Hydroxide | Tested | Tested |
| 10% Sodium Hydroxide | Tested | Tested |
| 10% Ammonia | Tested | Tested |
| 5% Sodium Hypochlorite | Tested | Tested |
| 10% Sodium Chloride | Tested | Tested |
| MEK | Tested | Tested |
| Acetone | Tested | Tested |
| Toluene | Tested | Tested |
| Methanol | Tested | Tested |
| Isopropyl Alcohol | Tested | Tested |
| Heptane | Tested | Tested |
| Mineral Spirits | Tested | Tested |
| Turpentine | Tested | Tested |
| Diesel Fuel | Tested | Tested |
| Kerosene | Tested | Tested |
| Gasoline | Tested | Tested |
| ASTM #3 Oil | Tested | Tested |
| SAE 20 Oil | Tested | Tested |
| Alconox® Detergent | Tested | Tested |
| Deionized Water | Tested | Tested |
Environmental & Aging Durability Testing
| Environmental Exposure Condition | Observation & Legibility Result |
|---|---|
| Service temperature | -18 to 54 °C |
Verified Target Applications & Use Cases
- Industrial rating plates, asset identification, and electrical component labeling.